No Additional PayPal Fees
Prices Lower than our Regular Pricelist Prices
Fast Support Reply

Biosemi

View as Grid List
Sort by
Display per page

Active Electrode for Biosemi Systems

Active Sensor Set with a 68-pole fine-pitch connector. 32*Pin-Type sensor with sintered Ag/AgCl tip and integrated low-noise CMOS pre-amplifier. Two-wire design. Standard cable length is 140cm. Electrode Sets are available in standard 10-20 label fashion or in the extended ABC label fashion.
A$ 2,335.20

Biosemi Active Electrode Repair Order

NEUROSPEC AG offers repairs/replacements for the Active Electrodes manufactured by Biosemi BV as below specified.

Please add each set separately to your basket (outside the standard 12 months warranty from date of purchase).
A$ 248.64

CMS/DRL Sensor Set External (Flat or Pin)

CMS/DRL External Sensor Set, use this instead of the CMS/DRL of the A-Set (cannot use both at the same time). Cable length 1.5m, 4 Pin DIN type plug (plugs into AUX1 of the AD Box), available as either Pin or Flat type.
From A$ 252.00

Diamond Electrode (Active to Passive adapter cable)

Active to Passive electrode adapter cable. Connects to the 8 EX inputs of the ActiveTwo (Biosemi) AD-box, and have an active electrode circuitry with a standard 1.5mm DIN touchproof connector - for standard passive electrodes (surface or needle).
A$ 109.20

ActiveTwo EEG Cap

ActiveTwo Standard EEG Cap with or without holders, comes with chin strap, ear slits and either 10-20 or ABCD label fashion (if empty cap is chosen the cap will come dotted according to 10-20, 64 dots). Cap comes in 15 different sizes from 34-66cm.
From A$ 433.44

Surgical Cap (no Holders)

The ECI Special Form/Surgical Form Cap is a strapless Electro-Cap designed to be used for different EEG purposes. The cap can be ordered as either standard surgical (no ear slits, no chin straps) or extended to cover also the neck. It fits the head securely, thereby eliminating the need for chin straps or a body harness. Cap does not come with electrodes or dotted for any electrode holder placements. Cap can be ordered in any different size, please specify when ordering.
A$ 663.60

ActiveTwo Cap Holder Kit

ActiveTwo Cap holders (available in different sizes), kit consists of body, lid and rubber washer. Comes with PDF instruction manual "How to Fit to Cap".
A$ 10.08

Water Resistant EEG Labels

Water Resistant EEG Labels for electrodes and cap holders, available as 10-20, ABCDEFGH or EXG style. 1 sheet per pack (labels can be peeled off). Labels are 100% water resistant.
A$ 58.80

ERGO Upgrade

Any ActiveTwo EEG System from Biosemi can be upgraded to include analogue input channels. Input used is on the front of the ADC box labeled ERGO in place of AUX2 or AUX3 (which ever is available). Upgrade includes: ERGO 2/4 input channels, wiring and AUX connector + label.

Caution: Input only non mains driven sensors, such as Respiration Belt, Microphone, various switches, etc.

Please note: ERGO can only be implemented if either AUX2 or AUX3 are unused. In case of AUX2 or AUX3 being occupied by GSR, we would replace the GSR module with a combined GSR/ERGO module.
From A$ 966.00

Analog Input Box (AIB)

The Analog Input Box (AIB) allows connection of sensors (battery or mains driven) or the attachment of any signal generating products. All the inputs are processed differential. For each signal which are connected to the AIB box, an AIB channel is required. The Input range of the AIB is +/-1 Volt (2 Volt peak to peak). Standard the AIB is equipped with 8 channels (can be ordered with a maximum of 32 channels). The speedmode switch on the frontpanel of the AIB should always be set to 8. With an AIB, the ActiveTwo EEG only works at speedmode 4. Package comes with the AIB box (8 channels) fitted with a D-SUB 37 socket, the power socket, an IN/OUT socket for the connection of the optical fibers; 1 x optical fiber and 1 x power supply. Please note: the Analog Input Box can be internally switched to 2-0 Volt. Select number of input channels, includes fitting of channels.
From A$ 7,476.00

GSR Sensor

Galvanic Skin Response (GSR) Sensor Electrode Set; includes a pair of steel electrodes suitable for GSR on the Biosemi ActiveTwo. Cable length of sensor is approximately 1.5m, terminates in a 7 pin DIN plug which plugs directly into the AUX2/AUX3 socket (which ever is available) of the Biosemi ActiveTwo AD Box.


Specifications of the stimulator: 16Hz, AC, the stimulus-current can be as low as 1uA. Measurements in ActiView in nS.


Please note: We install the GSR module here in our office. If an ERGO module is installed already, we would replace the ERGO module with a combo GSR/ERGO module and include a GSR/ERGO Splitter Cable.

A$ 327.60